Qlogic SANbox2-64 Guía de usuario

Simplify059060-00 01 PRELIMINARY Page iQLogic Fibre Channel SwitchAlarm Message GuideFirmware Version 4.1

2 – Events and AlarmsDisplaying the Events Using the Command Line Interface2-2 PRELIMINARY 59060-00 0102.2Displaying the Events Using the Command Lin

2 – Events and AlarmsConfiguring Port Alarm Thresholds59060-00 01 PRELIMINARY 2-302. Open an FTP session on the switch and login with the account nam

2 – Events and AlarmsConfiguring Port Alarm Thresholds2-4 PRELIMINARY 59060-00 010Notes

59060-00 01 PRELIMINARY 3-1Section 3Alarm MessagesThis section describes the alarm message format and lists the alarm messages in message ID sequence

3 – Alarm MessagesAlarm Messages3-2 PRELIMINARY 59060-00 010[A1000.0001] [SM] [Delaying switch reset - switch is busy]Meaning: The switch is busy and

3 – Alarm MessagesAlarm Messages59060-00 01 PRELIMINARY 3-30A1000.000C] [SM] [The switch will be shutdown several seconds]Meaning: The switch is bein

3 – Alarm MessagesAlarm Messages3-4 PRELIMINARY 59060-00 010[A1000.0017] [SM] [The switch is being shutdown while in config edit mode]Meaning: The sw

3 – Alarm MessagesAlarm Messages59060-00 01 PRELIMINARY 3-50[A1003.0001] [Zoning] [Maximum of <zoneSets> inactive ZoneSets exceeded during merg

3 – Alarm MessagesAlarm Messages3-6 PRELIMINARY 59060-00 010[A1003.000C] [Zoning] [Fabric Busy, Failing lock request from domain <domain #>]Mea

3 – Alarm MessagesAlarm Messages59060-00 01 PRELIMINARY 3-70[A1003.001D] [Zoning] [Failing SFC, total zones in zonesets limit would be exceeded]Meani

Page ii PRELIMINARY 59060-00 010ProductName ProductTypeUser’s Guide© 2000–2004 QLogic CorporationFirst Printed: April 2004All Rights Reserved Worldwi

3 – Alarm MessagesAlarm Messages3-8 PRELIMINARY 59060-00 010[A1003.002E] [Zoning] [Error on zone merge (code= 0x<code>, reason= 0x<reason>

3 – Alarm MessagesAlarm Messages59060-00 01 PRELIMINARY 3-90[A1004.0000] [Eport] [BBCredits zero, isolating]Meaning: An ISL failed because there was

3 – Alarm MessagesAlarm Messages3-10 PRELIMINARY 59060-00 010[A1004.000A] [Eport] [Eport Isolating due to EFP Domain Overlap]Meaning: An E_Port isola

3 – Alarm MessagesAlarm Messages59060-00 01 PRELIMINARY 3-110[A1004.0011] [Eport] [Eport Isolating due to Remote switch Isolated]Meaning: An E_Port i

3 – Alarm MessagesAlarm Messages3-12 PRELIMINARY 59060-00 010[A1004.001B] [Eport] [ELP indicates invalid Revision]Meaning: Revision number supplied o

3 – Alarm MessagesAlarm Messages59060-00 01 PRELIMINARY 3-130[A1004.0020] [Eport] [R_A_TOV mismatch indicated on ELP]Meaning: An E_Port isolated beca

3 – Alarm MessagesAlarm Messages3-14 PRELIMINARY 59060-00 010[A1004.0027] [Eport] [Requested domain id <domain id> not available]Meaning: The r

3 – Alarm MessagesAlarm Messages59060-00 01 PRELIMINARY 3-150[A1004.002D] [Eport] [Noninterop Legacy switch setting makes domain/port zoning non-inte

3 – Alarm MessagesAlarm Messages3-16 PRELIMINARY 59060-00 010[A1005.0000] [SM] [Illegal Alias name <name> read from zoning merge]Meaning: An il

3 – Alarm MessagesAlarm Messages59060-00 01 PRELIMINARY 3-170[A1005.0000] [SM] [Illegal ZoneSet name <name> read from zoning merge]Meaning: An

59060-00 01 PRELIMINARY Page iiiTable of ContentsSection 1 Introduction1.1 Intended Audience ...

3 – Alarm MessagesAlarm Messages3-18 PRELIMINARY 59060-00 010[A1005.000C] [nserver] [Requested credit not granted for port % d, donors at time, %s]Me

3 – Alarm MessagesAlarm Messages59060-00 01 PRELIMINARY 3-190[A1005.0015] [SM] [Port <port> was DISABLED before NDCLA due to excessive errors -

3 – Alarm MessagesAlarm Messages3-20 PRELIMINARY 59060-00 010[A1005.0028] [SM] [Zoning edit session has been preempted by a zoning merge !]Meaning: Z

3 – Alarm MessagesAlarm Messages59060-00 01 PRELIMINARY 3-210[A3014.0001] [SM] [Blade in slot <slot> set Down due to failure of all AuxPorts]Me

3 – Alarm MessagesAlarm Messages3-22 PRELIMINARY 59060-00 010[A4003.0001] [SM Port: <port no.>] [LOS errors of <errors> hit rising trigge

3 – Alarm MessagesAlarm Messages59060-00 01 PRELIMINARY 3-230[A4083.0001] [SM Port: <port no.>] [LOS errors of <errors> hit falling trigg

3 – Alarm MessagesAlarm Messages3-24 PRELIMINARY 59060-00 010Notes

Page iv PRELIMINARY 59060-00 01ProductName ProductTypeUser’s Guide0Notes

59060-00 01 PRELIMINARY 1-1Section 1IntroductionThis manual describes the alarm messages for the following QLogic of Fibre Channel switch products us

1 – IntroductionRelated Materials1-2 PRELIMINARY 59060-00 010 SANbox2-8c/16 Switch Management User’s Guide, publication number 59022-09. SANbox2-64

1 – IntroductionTechnical Support59060-00 01 PRELIMINARY 1-301.3Technical SupportCustomers should contact their authorized maintenance provider for t

1 – IntroductionContact Information1-4 PRELIMINARY 59060-00 010Notes

59060-00 01 PRELIMINARY 2-1Section 2Events and AlarmsMessages originate from the switch or from the SANbox Manager application in response to events