Qlogic QLogic 12000 Series Guía de instalación Pagina 15
- Pagina / 134
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
1–Installation
Installation Tasks Checklist
D000140-001 D 1-5
Whether or not the UPS unit also provides online protection.
Installation Tasks Checklist
To perform the actual switch installation, the site implementation engineer must
perform the following tasks, which are detailed in this section.
1. Check the installation site to verify the installation of cabinet power feeds,
rails, and grounding.
2. Unpack the equipment and inspect for any shipping damage. Any shipping
damage should be reported to the shipping company.
3. Verify that the equipment shipped matches the packing list.
4. Mark the rack and install the mounting rails.
5. Physically install the switch in the rack.
Tools and Equipment Required
An ESD wrist strap
A #2 Phillips screwdriver
An M6 HEX nut wrench
Pen (felt-tip) to mark the mounting holes
Lifting device (e.g., pallet jack) for the 12800-360 and 12800-180
Check the Installation Site
The switches are designed to be installed in an existing server cabinet (not a telco
cabinet), where it can be mounted in a standard equipment rack.
Be sure of the following:
The cabinet has a full earth ground to provide reliable grounding.
There is enough room to work on the equipment.
The equipment will have enough clearance for front and rear access.
The IB cables can be accessed easily.
Water or moisture cannot enter the switch.
CAUTION!
Be sure to review the safety information before starting the installation and during the
installation process (refer to Appendix B.
- QLogic 12000 Series 1
- Document Revision History 2
- Table of Contents 3
- Hardware Installation Guide 4
- Intended Audience 7
- Documentation Conventions 7
- cd /root and press ENTER 8
- License Agreements 9
- Technical Support 9
- Knowledge Database 10
- 1 Installation 11
- Cable Requirements 12
- Uninterruptible Power Supply 14
- Installation Tasks Checklist 15
- Mark the Rack 16
- 12200/12300 Installation 17
- 1–Installation 18
- 1-8 D000140-001 D 18
- D000140-001 D 1-9 19
- Installation 20
- Figure 1-6. 12200 Hat Rails 20
- D000140-001 D 1-11 21
- 12800-040 Installation 22
- Installation Tasks 23
- 1-14 D000140-001 D 24
- D000140-001 D 1-15 25
- 12800-120 Installation 26
- D000140-001 D 1-17 27
- 1-18 D000140-001 D 28
- D000140-001 D 1-19 29
- 1-20 D000140-001 D 30
- D000140-001 D 1-21 31
- 1-22 D000140-001 D 32
- D000140-001 D 1-23 33
- 12800-180 Installation 34
- D000140-001 D 1-25 35
- 1-26 D000140-001 D 36
- D000140-001 D 1-27 37
- 1-28 D000140-001 D 38
- D000140-001 D 1-29 39
- 1-30 D000140-001 D 40
- D000140-001 D 1-31 41
- 12800-360 Installation 42
- D000140-001 D 1-33 43
- 1-34 D000140-001 D 44
- 1-36 D000140-001 D 46
- D000140-001 D 1-37 47
- 1-38 D000140-001 D 48
- D000140-001 D 1-39 49
- 1-40 D000140-001 D 50
- D000140-001 D 1-41 51
- 1-42 D000140-001 D 52
- D000140-001 D 1-43 53
- 1-44 D000140-001 D 54
- D000140-001 D 1-45 55
- 1-46 D000140-001 D 56
- Connecting Power 57
- Figure 1-41. DC ON/OFF Switch 58
- Guidelines 59
- User Site Installation 60
- Start-up Procedures 61
- 1-52 D000140-001 D 62
- D000140-001 D 1-53 63
- 1-54 D000140-001 D 64
- Enabling 8X Ports 65
- Figure 1-49. 8X Ports Enabled 66
- D000140-001 D 1-57 67
- 1-58 D000140-001 D 68
- Figure 1-52. 8X Ports Enabled 69
- 1-60 D000140-001 D 70
- Component LEDs 71
- Chassis Status and Attention 72
- Fault Tolerant 72
- Service Required 72
- MRL Active 72
- Figure 1-55. MRL Active LED 73
- Leaf Module 74
- Spine Module 75
- SEEB Module 76
- 12200 and 12300 77
- 12800 Fans and Power Supplies 78
- Power Supply LEDs 79
- 1-70 D000140-001 D 80
- Procedures 81
- 1-72 D000140-001 D 82
- D000140-001 D 1-73 83
- 1-74 D000140-001 D 84
- D000140-001 D 1-75 85
- 1-76 D000140-001 D 86
- D000140-001 D 1-77 87
- QLogic 12000 Six-Port Upgrade 88
- 1-80 D000140-001 D 90
- A QLogic 12000 Series 91
- Environmental Specifications 92
- Power Specifications 94
- Power Distribution Guidelines 96
- Table A-4. AC Plug Types 97
- D000140-001 D A-9 99
- 12800 Series 100
- A-10 D000140-001 D 100
- B Safety and Regulatory 101
- Safety Information 102
- B-2 D000140-001 D 102
- Statement 2: 103
- B-4 D000140-001 D 104
- ステートメント 2： 105
- Statement 3: 106
- Uttalande 3: 107
- Kijelentés 3: 107
- Инструкция 3: 107
- ステートメント 3： 107
- Statement 4: 108
- D000140-001 D B-9 109
- Statement 5: 110
- Uttalande 5: 111
- Kijelentés 5: 111
- Инструкция 5: 111
- ステートメント 5： 111
- Statement 6: 112
- Kijelentés 6: 113
- Инструкция 6: 113
- ステートメント 6： 113
- Statement 7: 114
- D000140-001 D B-15 115
- ステートメント 7： 116
- D000140-001 D B-17 117
- B-18 D000140-001 D 118
- C Serial Port Pinouts 119
- Serial Port Pinouts 120
- C-2 D000140-001 D 120
- P5-Rx P5 P6-Tx 120
- P6-Gnd P4 P4-Gnd 120
- P4-Tx P3 P5-Rx 120
- D000140-001 D C-3 121
- C-4 D000140-001 D 122
- D FRU Replacement 123
- QLogic 12300 124
- Fan/Power Supply Replacement 125
- QLogic 12800 Series 126
- Replacement Procedures 127
- Power Supply Replacement 128
- Leaf Module Replacement 129
- Spine Module Replacement 131
- Management Module Replacement 132
Relacionado con productos y manuales para Los conmutadores de red Qlogic QLogic 12000 Series
(46 paginas)
(114 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales