Qlogic SANbox2-8c Guía de instalación Pagina 63
- Pagina / 162
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5 – Diagnostics/Troubleshooting
Chassis Diagnostics
59042-01 A 5-7
5.2
Chassis Diagnostics
Chassis diagnostics are indicated by the chassis LEDs as shown in Figure 5-3.
Figure 5-3. Chassis LEDs
The following conditions are described:
■ Over Temperature LED is illuminated
■ Input Power LED is extinguished
■ Fan Fail LED is illuminated
5.2.1
Over Temperature LED is Illuminated
The Over Temperature LED illuminates to indicate that the switch logic circuitry is
overheating. If the Over Temperature LED illuminates, do the following:
1. Inspect the chassis fan. Is the intake opening clear? Is the fan operating and
producing air flow?
■ Yes - Continue.
■ No - Remove any debris from fan intake and exhaust if necessary. If
the condition remains, continue.
2. Consider the ambient air temperature near the switch and clearance around
the switch. Make necessary corrections. If the condition remains, contact
your authorized maintenance provider.
Over Temperature LED
(Yellow)
Fan Fail LED
(Yellow)
Heartbeat LED
(Yellow)
Input Power LED
(Green)
- Installation Guide 1
- Document Revision History 2
- Table of Contents 3
- Section 3 Planning 4
- Section 4 Installation 4
- 59042-01 A Page v 5
- Appendix A Specifications 6
- Page viii 59042-01 A 8
- Introduction 9
- Related Materials 10
- Safety Notices 11
- Sicherheitshinweise 11
- Communications Statements 12
- Statement 12
- CE Statement 13
- VCCI Class A Statement 14
- BSMI Class A Statement 14
- Laser Safety Information 15
- Accessible Parts 15
- Pièces Accessibles 15
- Zugängliche Teile 15
- Technical Support 16
- Availability 16
- Training 16
- Contact Information 16
- General Description 17
- Chassis Controls and LEDs 18
- Reset/Force PROM Button 18
- Resetting a Switch 19
- Over Temperature LED (Yellow) 19
- Fan Fail LED (Yellow) 19
- Heartbeat LED (Yellow) 20
- Input Power LED (Green) 20
- Fibre Channel Ports 20
- Logged-In LED 21
- Activity LED 21
- Port Modes 22
- Fabric Ports 22
- Translated Loop Port 23
- Expansion Port 23
- Ethernet Port 24
- Serial Port 25
- Power Supply and Fan 26
- Switch Management 26
- Planning 27
- Multiple Chassis Fabrics 28
- Common Topologies 29
- Cascade Topology 29
- Mesh Topology 30
- Multistage Topology 31
- Performance 32
- Distance 32
- Bandwidth 33
- Device Access 34
- Soft Zones 35
- Fabric Management 36
- Fabric Security 37
- 3 – Planning 38
- 3-12 59042-01 A 38
- Installation 39
- Environmental Conditions 40
- Installing a Switch 40
- Mount the Switch 41
- Install SFP Transceivers 42
- 4 – Installation 43
- 59042-01 A 4-5 43
- 4-6 59042-01 A 44
- SANbox2 Login: admin 46
- Password: ******** 46
- Install SANbox Manager 47
- 4-10 59042-01 A 48
- ./sansurfer_linux_install.bin 49
- 4-12 59042-01 A 50
- Configure the Switch 51
- Configure the Ports 52
- Cable Devices to the Switch 52
- Installing Firmware 52
- 59042-01 A 4-15 53
- 4-16 59042-01 A 54
- Powering Down a Switch 55
- 4-18 59042-01 A 56
- Diagnostics/Troubleshooting 57
- Force PROM Mode Pattern 58
- Fatal Error Blink Pattern 58
- POST Diagnostics 59
- 59042-01 A 5-3 59
- 5-4 59042-01 A 60
- Logged-In LED Indications 61
- Chassis Diagnostics 63
- Fan Fail LED is Illuminated 64
- Recovering a Switch 65
- Force PROM – Exit 66
- Force PROM – Image Unpack 66
- Force PROM – Copy Log Files 67
- Force PROM – Reset Switch 67
- 5-12 59042-01 A 68
- Specifications 69
- Switch Maintainability 70
- Switch Dimensions 71
- Switch Electrical 71
- Switch Environmental 71
- A – Specifications 72
- A-4 59042-01 A 72
- 59042-01 A A-5 73
- A-6 59042-01 A 74
- /> telnet 123.45.67.890 75
- Command Syntax 76
- Commands 77
- Admin Command 78
- Alias Command 79
- B-6 59042-01 A 80
- Config Command 81
- B-8 59042-01 A 82
- SANbox2 $> date 83
- Tue Nov 12 07:51:24 2002 83
- SANbox2 #> admin start 84
- SANbox2 $> admin end 84
- Help Command 85
- History Command 86
- Image Command 87
- SANbox2 (admin) #> lip 2 88
- Passwd Command 89
- Ps Command 90
- Quit Command 91
- Reset Command 92
- Set Command 97
- SANbox2 $> set beacon on 98
- Command succeeded 98
- SANbox2 $> set beacon off 98
- B – Command Line Interface 104
- Set Config Command 104
- B-30 59042-01 A 104
- 59042-01 A B-31 105
- B-32 59042-01 A 106
- Set Log Command 107
- B-34 59042-01 A 108
- 59042-01 A B-35 109
- Set Port Command 110
- Set Setup Command 111
- 59042-01 A B-39 113
- B-40 59042-01 A 114
- Show Command 115
- B-42 59042-01 A 116
- B-46 59042-01 A 120
- 59042-01 A B-47 121
- B-48 59042-01 A 122
- 59042-01 A B-49 123
- B-50 59042-01 A 124
- Show Config Command 125
- B-52 59042-01 A 126
- 59042-01 A B-53 127
- SANbox2 $> show log level 128
- Show Log Command 129
- 59042-01 A B-55 129
- Show Perf Command 130
- 59042-01 A B-57 131
- Show Setup Command 132
- 59042-01 A B-59 133
- Shutdown Command 134
- Test Command 135
- B-62 59042-01 A 136
- 59042-01 A B-63 137
- SANbox2 $> uptime 138
- User Command 139
- B-66 59042-01 A 140
- SANbox2 $> whoami 141
- User name:admin@session2 141
- Switch name:SANbox2 141
- Switch domain ID:1 141
- Zone Command 142
- ■ Alias name 143
- B-70 59042-01 A 144
- zone_set_1 145
- Zoneset Command 146
- 59042-01 A B-73 147
- B-74 59042-01 A 148
- Zoning Command 149
- B-76 59042-01 A 150
- 59042-01 A B-77 151
- B-78 59042-01 A 152
- Glossary 153
- Glossary-2 59042-01 A 154
- 59042-01 A Glossary-3 155
- Glossary-4 59042-01 A 156
- 59042-01 A Index-1 157
- Index-2 59042-01 A 158
- 59042-01 A Index-3 159
- Index-4 59042-01 A 160
- 59042-01 A Index-5 161
- Index-6 59042-01 A 162
Relacionado con productos y manuales para Los conmutadores de red Qlogic SANbox2-8c
(130 paginas)
(42 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales