Qlogic QLogic 12000 Series Guía de instalación descargar pdf (Pagina 16)

1–Installation

Installation Tasks Checklist

1-6 D000102-000 B

It is recommended that cabinet anti-tip devices are used. This is especially true if

installing or removing a switch in the upper half of the cabinet when the lower half

is empty.

Mark the Rack

Allow enough vertical space in the rack for each specific switch installation.

1. Determine the location in the rack of the bottom of the switch.

2. Mark the upper (if applicable) and lower mounting positions on the vertical rails

on the front of the rack.

3. Mark the upper (if applicable) and lower mounting positions on the vertical rails

on the back of the rack.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 113 114

QLogic 12000 Series 1
Document Revision History 2
Table of Contents 3
Hardware Installation Guide 4
C Serial Port Pinouts 5
D FRU Replacement 5
Intended Audience 7
Documentation Conventions 7
License Agreements 8
Technical Support 10
4 D000102-000 B 10
1 Installation 11
Cable Requirements 12
Uninterruptible Power Supply 14
Installation Tasks Checklist 15
Mark the Rack 16
12200/12300 Installation 17
1–Installation 18
1-8 D000102-000 B 18
Installation 19
1-10 D000102-000 B 20
D000102-000 B 1-11 21
Figure 1-10 12200 Hat Rails 22
D000102-000 B 1-13 23
12800-180 Installation 24
D000102-000 B 1-15 25
1-16 D000102-000 B 26
D000102-000 B 1-17 27
Torque all screws to 30in-lb 28
D000102-000 B 1-19 29
Overview 30
Installation tasks 31
Assemble the Support Shelf 32
D000102-000 B 1-23 33
1-24 D000102-000 B 34
D000102-000 B 1-25 35
1-26 D000102-000 B 36
D000102-000 B 1-27 37
1-28 D000102-000 B 38
D000102-000 B 1-29 39
1-30 D000102-000 B 40
D000102-000 B 1-31 41
Connecting Power 42
Figure 1-29 DC ON/OFF Switch 43
Guidelines 44
User Site Installation 45
Start-up Procedures 46
D000102-000 B 1-37 47
D000102-000 B 1-39 49
1-40 D000102-000 B 50
Component LEDs 51
Chassis Status and Attention 52
Fault Tolerant 52
Service Required 52
MRL Active 53
Figure 1-37 MRL Active LED 53
Leaf Module 54
Spine Module 55
SEEB Module 56
12200 and 12300 57
12800 Fans and Power Supplies 58
Power Supply LEDs 59
1-50 D000102-000 B 60
Procedures 61
1-52 D000102-000 B 62
D000102-000 B 1-53 63
1-54 D000102-000 B 64
D000102-000 B 1-55 65
1-56 D000102-000 B 66
D000102-000 B 1-57 67
1-58 D000102-000 B 68
A QLogic 12000 Series 69
Environmental Specifications 70
12800 Series 71
Power Specifications 72
Power Distribution Guidelines 73
Table A-4. AC Plug Types 74
D000102-000 B A-7 75
A-8 D000102-000 B 76
B Safety and Regulatory 77
Safety Information 78
B-2 D000102-000 B 78
Statement 2: 79
B-4 D000102-000 B 80
ステートメント 2： 81
Statement 3: 82
Uttalande 3: 83
Kijelentés 3: 83
Инструкция 3: 83
ステートメント 3： 83
Statement 4: 84
D000102-000 B B-9 85
Statement 5: 86
Uttalande 5: 87
Kijelentés 5: 87
Инструкция 5: 87
ステートメント 5： 87
Statement 6: 88
Kijelentés 6: 89
Инструкция 6: 89
ステートメント 6： 89
Statement 7: 90
D000102-000 B B-15 91
ステートメント 7： 92
D000102-000 B B-17 93
B-18 D000102-000 B 94
C–Serial Port Pinouts 96
C-2 D000102-000 B 96
P5-Rx P5 P6-Tx 96
P6-Gnd P4 P4-Gnd 96
P4-Tx P3 P5-Rx 96
D000102-000 B C-3 97
C-4 D000102-000 B 98
QLogic 12300 100
Chassis Replacement 101
D–FRU Replacement 102
D-4 D000102-000 B 102
QLogic 12800 Series 103
Removal Procedures 104
Replacement Procedures 105
Power Supply Replacement 106
Leaf Module Replacement 107
Spine Module Replacement 109
Management Module Replacement 110
D000102-000 B D-13 111
D-14 D000102-000 B 112

Comentarios a estos manuales

Sin comentarios

Qlogic QLogic 12000 Series Guía de instalación Pagina 16

Comentarios a estos manuales

Relacionado con productos y manuales para Los conmutadores de red Qlogic QLogic 12000 Series