Qlogic QLogic 12000 Series Guía de instalación descargar pdf (Pagina 27)

1–Installation

12800-180 Installation

D000102-000 B 1-17

WARNING!!

To avoid injury, do not lift manually when fully loaded. The 12800-180, when

fully-populated, weighs 270lbs (125kg). Use a mechanized lift only. For a

manual lift, unload the product to minimize the weight (an empty chassis

weighs 100lbs/45kg). Use a team of people appropriate to the weight of the

product and in conjunction with applicable laws and guidelines.

Figure 1-14 Mounting Flange Installation

5. Fasten the mounting flanges using M6 screws to the clip nuts that are

pre-installed in the rack. There are six (6) screws per mounting flange. Torque

to 30in-lb.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 113 114

QLogic 12000 Series 1
Document Revision History 2
Table of Contents 3
Hardware Installation Guide 4
C Serial Port Pinouts 5
D FRU Replacement 5
Intended Audience 7
Documentation Conventions 7
License Agreements 8
Technical Support 10
4 D000102-000 B 10
1 Installation 11
Cable Requirements 12
Uninterruptible Power Supply 14
Installation Tasks Checklist 15
Mark the Rack 16
12200/12300 Installation 17
1–Installation 18
1-8 D000102-000 B 18
Installation 19
1-10 D000102-000 B 20
D000102-000 B 1-11 21
Figure 1-10 12200 Hat Rails 22
D000102-000 B 1-13 23
12800-180 Installation 24
D000102-000 B 1-15 25
1-16 D000102-000 B 26
D000102-000 B 1-17 27
Torque all screws to 30in-lb 28
D000102-000 B 1-19 29
Overview 30
Installation tasks 31
Assemble the Support Shelf 32
D000102-000 B 1-23 33
1-24 D000102-000 B 34
D000102-000 B 1-25 35
1-26 D000102-000 B 36
D000102-000 B 1-27 37
1-28 D000102-000 B 38
D000102-000 B 1-29 39
1-30 D000102-000 B 40
D000102-000 B 1-31 41
Connecting Power 42
Figure 1-29 DC ON/OFF Switch 43
Guidelines 44
User Site Installation 45
Start-up Procedures 46
D000102-000 B 1-37 47
D000102-000 B 1-39 49
1-40 D000102-000 B 50
Component LEDs 51
Chassis Status and Attention 52
Fault Tolerant 52
Service Required 52
MRL Active 53
Figure 1-37 MRL Active LED 53
Leaf Module 54
Spine Module 55
SEEB Module 56
12200 and 12300 57
12800 Fans and Power Supplies 58
Power Supply LEDs 59
1-50 D000102-000 B 60
Procedures 61
1-52 D000102-000 B 62
D000102-000 B 1-53 63
1-54 D000102-000 B 64
D000102-000 B 1-55 65
1-56 D000102-000 B 66
D000102-000 B 1-57 67
1-58 D000102-000 B 68
A QLogic 12000 Series 69
Environmental Specifications 70
12800 Series 71
Power Specifications 72
Power Distribution Guidelines 73
Table A-4. AC Plug Types 74
D000102-000 B A-7 75
A-8 D000102-000 B 76
B Safety and Regulatory 77
Safety Information 78
B-2 D000102-000 B 78
Statement 2: 79
B-4 D000102-000 B 80
ステートメント 2： 81
Statement 3: 82
Uttalande 3: 83
Kijelentés 3: 83
Инструкция 3: 83
ステートメント 3： 83
Statement 4: 84
D000102-000 B B-9 85
Statement 5: 86
Uttalande 5: 87
Kijelentés 5: 87
Инструкция 5: 87
ステートメント 5： 87
Statement 6: 88
Kijelentés 6: 89
Инструкция 6: 89
ステートメント 6： 89
Statement 7: 90
D000102-000 B B-15 91
ステートメント 7： 92
D000102-000 B B-17 93
B-18 D000102-000 B 94
C–Serial Port Pinouts 96
C-2 D000102-000 B 96
P5-Rx P5 P6-Tx 96
P6-Gnd P4 P4-Gnd 96
P4-Tx P3 P5-Rx 96
D000102-000 B C-3 97
C-4 D000102-000 B 98
QLogic 12300 100
Chassis Replacement 101
D–FRU Replacement 102
D-4 D000102-000 B 102
QLogic 12800 Series 103
Removal Procedures 104
Replacement Procedures 105
Power Supply Replacement 106
Leaf Module Replacement 107
Spine Module Replacement 109
Management Module Replacement 110
D000102-000 B D-13 111
D-14 D000102-000 B 112

Comentarios a estos manuales

Sin comentarios

Qlogic QLogic 12000 Series Guía de instalación Pagina 27

Comentarios a estos manuales

Relacionado con productos y manuales para Los conmutadores de red Qlogic QLogic 12000 Series