Qlogic SANbox 5600 Series Guía de instalación Pagina 147
- Pagina / 280
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
B – Command Line Interface
Firmware Install Command
59096-02 C B-25
A
Firmware Install Command
Downloads firmware from a remote host to the switch, installs the firmware, then
resets the switch (without a power-on self test) to activate the firmware. This is
disruptive to I/O traffic. To perform a non-disruptive firmware installation, refer to
the ”Image Command” on page B-38.
The command prompts you for the following:
IP address of the remote host
An account name and password on the remote host
Pathname for the firmware image file
Authority Admin
Syntax firmware install
Examples The following is an example of the Firmware Install command:
SANbox (admin) #> firmware install
Warning: Installing new firmware requires a switch reset.
Continuing with this action will terminate all management sessions,
including any Telnet sessions. When the firmware activation is complete,
you may log in to the switch again.
Do you want to continue? [y/n]: y
Press 'q' and the ENTER key to abort this command.
User Account : johndoe
IP Address : 10.20.33.130
Source Filename : 5.0.00.11_mpc
About to install image. Do you want to continue? [y/n] y
Connected to 10.20.33.130 (10.20.33.130).
220 localhost.localdomain FTP server (Version wu-2.6.1-18) ready.
331 Password required for johndoe.
Password: xxxxxxxxx
230 User johndoe logged in.
bin
200 Type set to I.
verbose
Verbose mode off.
This may take several seconds...
The switch will now reset.
Connection closed by foreign host.
- Installation Guide 1
- Document Revision History 2
- Table of Contents 3
- Section 3 Planning 4
- Section 4 Installation 5
- Section 6 Removal/Replacement 6
- Appendix A Specifications 6
- 59096-02 C Page vii 7
- 59096-02 C Page ix 9
- Page x 59096-02 C 10
- Introduction 11
- Related Materials 12
- Safety Notices 13
- Sicherheitshinweise 13
- Communications Statements 13
- Statement 14
- CE Statement 15
- VCCI Class A Statement 16
- Laser Safety Information 16
- Accessible Parts 17
- Pièces Accessibles 17
- Zugängliche Teile 17
- General Public License 18
- Preamble 18
- 1 – Introduction 19
- 59096-02 C 1-9 19
- 1-10 59096-02 C 20
- 59096-02 C 1-11 21
- 1-12 59096-02 C 22
- 59096-02 C 1-13 23
- 1-14 59096-02 C 24
- 59096-02 C 1-15 25
- Technical Support 26
- Availability 26
- Training 26
- Contact Information 27
- 1-18 59096-02 C 28
- General Description 29
- Chassis Controls and LEDs 30
- Maintenance Button 31
- Resetting a Switch 31
- Chassis LEDs 32
- Input Power LED (Green) 32
- Heartbeat LED (Green) 32
- System Fault LED (Amber) 33
- Fibre Channel Ports 33
- Port LEDs 34
- Port Logged-In LED (Green) 34
- Port Activity LED (Green) 35
- Transceivers 35
- Port Types 35
- Ethernet Port 36
- Serial Port 37
- Power Supplies and Fans 38
- Switch Management 39
- SANsurfer Switch Manager 39
- File Transfer Protocol 40
- Planning 41
- Device Access 42
- Soft Zones 43
- Performance 44
- Distance 44
- Bandwidth 45
- Feature Licensing 46
- Multiple Chassis Fabrics 46
- Optimizing Device Performance 46
- 3 – Planning 47
- 59096-02 C 3-7 47
- Stacking 48
- 59096-02 C 3-9 49
- Common Topologies 50
- Cascade Topology 50
- Mesh Topology 51
- Multistage Topology 52
- Switch Services 53
- Fabric Security 54
- Connection Security 55
- Device Security 56
- 59096-02 C 3-17 57
- 3-18 59096-02 C 58
- Switch_2 58
- 3-20 59096-02 C 60
- 3-22 59096-02 C 62
- 3-24 59096-02 C 64
- 59096-02 C 3-25 65
- MS Group: Group_1 65
- User Account Security 66
- 3-28 59096-02 C 68
- Installation 69
- Switch Power Requirements 70
- Environmental Conditions 70
- Installing a Switch 70
- Mount the Switch 71
- 4 – Installation 72
- 4-4 59096-02 C 72
- Install Transceivers 74
- Configure the Workstation 77
- SANsurfer Management Suite 81
- SMS Installation for Windows 81
- 4-14 59096-02 C 82
- SMS Installation for Linux 83
- SMS Installation for Solaris 85
- 4-20 59096-02 C 88
- 59096-02 C 4-21 89
- 4-22 59096-02 C 90
- Configure the Switch 91
- Cable Devices to the Switch 93
- Install Firmware 93
- 4-26 59096-02 C 94
- 95
- 4-28 59096-02 C 96
- Diagnostics/Troubleshooting 97
- Chassis Diagnostics 98
- 5-2 59096-02 C 98
- Heartbeat LED Blink Patterns 99
- System Error Blink Pattern 100
- Logged-In LED Indications 103
- E_Port Isolation 104
- Excessive Port Errors 105
- 5-10 59096-02 C 106
- Power Supply Diagnostics 107
- Recovering a Switch 108
- Maintenance – Exit 109
- Maintenance – Image Unpack 109
- Maintenance – Copy Log Files 110
- Maintenance – Reset Switch 111
- 5-16 59096-02 C 112
- Removal/Replacement 113
- 6 – Removal/Replacement 114
- 6-2 59096-02 C 114
- 6-4 59096-02 C 116
- Specifications 117
- Maintainability 119
- Fabric Management 119
- Dimensions 120
- Electrical 120
- Environmental 120
- A – Specifications 121
- 59096-02 C A-5 121
- Regulatory Certifications 122
- Command Line Interface 123
- User Accounts 124
- Modifying a Configuration 125
- Commands 128
- Admin Command 130
- Alias Command 131
- B – Command Line Interface 132
- B-10 59096-02 C 132
- CIM Command 133
- B-12 59096-02 C 134
- CIMListener Command 135
- B-14 59096-02 C 136
- CIMSubscription Command 137
- B-16 59096-02 C 138
- Config Command 139
- B-18 59096-02 C 140
- 59096-02 C B-19 141
- Create Command 142
- 59096-02 C B-21 143
- B-22 59096-02 C 144
- Date Command 145
- Feature Command 146
- Firmware Install Command 147
- Group Command 148
- Keywords add [group] 149
- B-32 59096-02 C 154
- 59096-02 C B-33 155
- Hardreset Command 156
- Help Command 157
- History Command 158
- Hotreset Command 159
- Image Command 160
- Lip Command 163
- Passwd Command 164
- Ping Command 165
- Ps Command 166
- Quit Command 167
- Reset Command 168
- 59096-02 C B-47 169
- Security Command 176
- 59096-02 C B-55 177
- B-56 59096-02 C 178
- 59096-02 C B-57 179
- Securityset Command 180
- 59096-02 C B-59 181
- B-60 59096-02 C 182
- Set Command 183
- B-62 59096-02 C 184
- 59096-02 C B-63 185
- Set Config Command 186
- 59096-02 C B-71 193
- B-72 59096-02 C 194
- 59096-02 C B-73 195
- B-74 59096-02 C 196
- 59096-02 C B-75 197
- Set Log Command 198
- 59096-02 C B-77 199
- B-78 59096-02 C 200
- 59096-02 C B-79 201
- Set Port Command 202
- 59096-02 C B-81 203
- Set Setup Command 204
- 59096-02 C B-89 211
- B-90 59096-02 C 212
- 59096-02 C B-91 213
- Show Command 214
- 59096-02 C B-93 215
- B-94 59096-02 C 216
- B-100 59096-02 C 222
- 59096-02 C B-101 223
- B-102 59096-02 C 224
- 59096-02 C B-103 225
- B-104 59096-02 C 226
- 59096-02 C B-105 227
- B-106 59096-02 C 228
- Show Config Command 229
- B-108 59096-02 C 230
- 59096-02 C B-109 231
- B-110 59096-02 C 232
- Show Log Command 233
- B-112 59096-02 C 234
- 59096-02 C B-113 235
- B-114 59096-02 C 236
- Show Perf Command 237
- B-116 59096-02 C 238
- 59096-02 C B-117 239
- Show Setup Command 240
- 59096-02 C B-119 241
- B-120 59096-02 C 242
- 59096-02 C B-121 243
- Shutdown Command 244
- Test Command 245
- Uptime Command 248
- User Command 249
- B-128 59096-02 C 250
- 59096-02 C B-129 251
- Whoami Command 252
- Zone Command 253
- B-132 59096-02 C 254
- 59096-02 C B-133 255
- B-134 59096-02 C 256
- Zoneset Command 257
- B-136 59096-02 C 258
- 59096-02 C B-137 259
- Zoning Command 260
- B-140 59096-02 C 262
- 59096-02 C B-141 263
- B-142 59096-02 C 264
- Glossary 265
- Glossary-2 59096-02 C 266
- 59096-02 C Glossary-3 267
- Glossary-4 59096-02 C 268
- 59096-02 C Glossary-5 269
- Glossary-6 59096-02 C 270
- Numerics 271
- Index-2 59096-02 C 272
- 59096-02 C Index-3 273
- Index-4 59096-02 C 274
- 59096-02 C Index-5 275
- Index-6 59096-02 C 276
- 59096-02 C Index-7 277
- Index-8 59096-02 C 278
- 59096-02 C Index-9 279
- Index-10 59096-02 C 280
Relacionado con productos y manuales para Los conmutadores de red Qlogic SANbox 5600 Series
(24 paginas)
(114 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales