Qlogic SANbox 5600 Series Guía de instalación Pagina 218
- Pagina / 280
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
B – Command Line Interface
Show Command
B-96 59096-02 C
S
InvalidDestAddr Invalid destination address detected.
LIP_AL_PD_ALPS Number of F7, AL_PS LIPs, or AL_PD (vendor specific) resets,
performed.
LIP_F7_AL_PS This LIP is used to reinitialize the loop. An L_Port, identified by
AL_PS, may have noticed a performance degradation and is
trying to restore the loop.
LIP_F8_AL_PS This LIP denotes a loop failure detected by the L_Port identified
by AL_PS.
LIP_F7_F7 A loop initialization primitive frame used to acquire a valid
AL_PA.
LIP_F8_F7 A loop initialization primitive frame used to indicate that a loop
failure has been detected at the receiver.
Link Failures Number of optical link failures detected by this port. A link failure
is a loss of synchronization or a loss of signal while not in the
offline state. A loss of signal causes the switch to attempt to
re-establish the link. If the link is not re-established, a link failure
is counted. A link reset is performed after a link failure.
Login Number of device logins
Logout Number of device logouts
LoopTimeouts A two (2) second timeout as specified by FC-AL-2.
LossOfSync Number of synchronization losses (>100 ms) detected by this
port. A loss of synchronization is detected by receipt of an
invalid transmission word.
PrimSeqErrors Primitive sequence errors detected.
RxLinkResets Number of link reset primitives received from an attached
device.
RxOfflineSeq Number of offline sequences received. An OLS is issued for link
initialization, a Receive & Recognize Not_Operational (NOS)
state, or to enter the offline state.
TotalErrors Total number of errors detected.
TotalLIPsRecvd Number of loop initialization primitive frames received by this
port.
TotalLIPsXmitd Number of loop initialization primitive frames transmitted by this
port.
Table B-27. Show Port Parameters (Continued)
Entry Description
- Installation Guide 1
- Document Revision History 2
- Table of Contents 3
- Section 3 Planning 4
- Section 4 Installation 5
- Section 6 Removal/Replacement 6
- Appendix A Specifications 6
- 59096-02 C Page vii 7
- 59096-02 C Page ix 9
- Page x 59096-02 C 10
- Introduction 11
- Related Materials 12
- Safety Notices 13
- Sicherheitshinweise 13
- Communications Statements 13
- Statement 14
- CE Statement 15
- VCCI Class A Statement 16
- Laser Safety Information 16
- Accessible Parts 17
- Pièces Accessibles 17
- Zugängliche Teile 17
- General Public License 18
- Preamble 18
- 1 – Introduction 19
- 59096-02 C 1-9 19
- 1-10 59096-02 C 20
- 59096-02 C 1-11 21
- 1-12 59096-02 C 22
- 59096-02 C 1-13 23
- 1-14 59096-02 C 24
- 59096-02 C 1-15 25
- Technical Support 26
- Availability 26
- Training 26
- Contact Information 27
- 1-18 59096-02 C 28
- General Description 29
- Chassis Controls and LEDs 30
- Maintenance Button 31
- Resetting a Switch 31
- Chassis LEDs 32
- Input Power LED (Green) 32
- Heartbeat LED (Green) 32
- System Fault LED (Amber) 33
- Fibre Channel Ports 33
- Port LEDs 34
- Port Logged-In LED (Green) 34
- Port Activity LED (Green) 35
- Transceivers 35
- Port Types 35
- Ethernet Port 36
- Serial Port 37
- Power Supplies and Fans 38
- Switch Management 39
- SANsurfer Switch Manager 39
- File Transfer Protocol 40
- Planning 41
- Device Access 42
- Soft Zones 43
- Performance 44
- Distance 44
- Bandwidth 45
- Feature Licensing 46
- Multiple Chassis Fabrics 46
- Optimizing Device Performance 46
- 3 – Planning 47
- 59096-02 C 3-7 47
- Stacking 48
- 59096-02 C 3-9 49
- Common Topologies 50
- Cascade Topology 50
- Mesh Topology 51
- Multistage Topology 52
- Switch Services 53
- Fabric Security 54
- Connection Security 55
- Device Security 56
- 59096-02 C 3-17 57
- 3-18 59096-02 C 58
- Switch_2 58
- 3-20 59096-02 C 60
- 3-22 59096-02 C 62
- 3-24 59096-02 C 64
- 59096-02 C 3-25 65
- MS Group: Group_1 65
- User Account Security 66
- 3-28 59096-02 C 68
- Installation 69
- Switch Power Requirements 70
- Environmental Conditions 70
- Installing a Switch 70
- Mount the Switch 71
- 4 – Installation 72
- 4-4 59096-02 C 72
- Install Transceivers 74
- Configure the Workstation 77
- SANsurfer Management Suite 81
- SMS Installation for Windows 81
- 4-14 59096-02 C 82
- SMS Installation for Linux 83
- SMS Installation for Solaris 85
- 4-20 59096-02 C 88
- 59096-02 C 4-21 89
- 4-22 59096-02 C 90
- Configure the Switch 91
- Cable Devices to the Switch 93
- Install Firmware 93
- 4-26 59096-02 C 94
- 95
- 4-28 59096-02 C 96
- Diagnostics/Troubleshooting 97
- Chassis Diagnostics 98
- 5-2 59096-02 C 98
- Heartbeat LED Blink Patterns 99
- System Error Blink Pattern 100
- Logged-In LED Indications 103
- E_Port Isolation 104
- Excessive Port Errors 105
- 5-10 59096-02 C 106
- Power Supply Diagnostics 107
- Recovering a Switch 108
- Maintenance – Exit 109
- Maintenance – Image Unpack 109
- Maintenance – Copy Log Files 110
- Maintenance – Reset Switch 111
- 5-16 59096-02 C 112
- Removal/Replacement 113
- 6 – Removal/Replacement 114
- 6-2 59096-02 C 114
- 6-4 59096-02 C 116
- Specifications 117
- Maintainability 119
- Fabric Management 119
- Dimensions 120
- Electrical 120
- Environmental 120
- A – Specifications 121
- 59096-02 C A-5 121
- Regulatory Certifications 122
- Command Line Interface 123
- User Accounts 124
- Modifying a Configuration 125
- Commands 128
- Admin Command 130
- Alias Command 131
- B – Command Line Interface 132
- B-10 59096-02 C 132
- CIM Command 133
- B-12 59096-02 C 134
- CIMListener Command 135
- B-14 59096-02 C 136
- CIMSubscription Command 137
- B-16 59096-02 C 138
- Config Command 139
- B-18 59096-02 C 140
- 59096-02 C B-19 141
- Create Command 142
- 59096-02 C B-21 143
- B-22 59096-02 C 144
- Date Command 145
- Feature Command 146
- Firmware Install Command 147
- Group Command 148
- Keywords add [group] 149
- B-32 59096-02 C 154
- 59096-02 C B-33 155
- Hardreset Command 156
- Help Command 157
- History Command 158
- Hotreset Command 159
- Image Command 160
- Lip Command 163
- Passwd Command 164
- Ping Command 165
- Ps Command 166
- Quit Command 167
- Reset Command 168
- 59096-02 C B-47 169
- Security Command 176
- 59096-02 C B-55 177
- B-56 59096-02 C 178
- 59096-02 C B-57 179
- Securityset Command 180
- 59096-02 C B-59 181
- B-60 59096-02 C 182
- Set Command 183
- B-62 59096-02 C 184
- 59096-02 C B-63 185
- Set Config Command 186
- 59096-02 C B-71 193
- B-72 59096-02 C 194
- 59096-02 C B-73 195
- B-74 59096-02 C 196
- 59096-02 C B-75 197
- Set Log Command 198
- 59096-02 C B-77 199
- B-78 59096-02 C 200
- 59096-02 C B-79 201
- Set Port Command 202
- 59096-02 C B-81 203
- Set Setup Command 204
- 59096-02 C B-89 211
- B-90 59096-02 C 212
- 59096-02 C B-91 213
- Show Command 214
- 59096-02 C B-93 215
- B-94 59096-02 C 216
- B-100 59096-02 C 222
- 59096-02 C B-101 223
- B-102 59096-02 C 224
- 59096-02 C B-103 225
- B-104 59096-02 C 226
- 59096-02 C B-105 227
- B-106 59096-02 C 228
- Show Config Command 229
- B-108 59096-02 C 230
- 59096-02 C B-109 231
- B-110 59096-02 C 232
- Show Log Command 233
- B-112 59096-02 C 234
- 59096-02 C B-113 235
- B-114 59096-02 C 236
- Show Perf Command 237
- B-116 59096-02 C 238
- 59096-02 C B-117 239
- Show Setup Command 240
- 59096-02 C B-119 241
- B-120 59096-02 C 242
- 59096-02 C B-121 243
- Shutdown Command 244
- Test Command 245
- Uptime Command 248
- User Command 249
- B-128 59096-02 C 250
- 59096-02 C B-129 251
- Whoami Command 252
- Zone Command 253
- B-132 59096-02 C 254
- 59096-02 C B-133 255
- B-134 59096-02 C 256
- Zoneset Command 257
- B-136 59096-02 C 258
- 59096-02 C B-137 259
- Zoning Command 260
- B-140 59096-02 C 262
- 59096-02 C B-141 263
- B-142 59096-02 C 264
- Glossary 265
- Glossary-2 59096-02 C 266
- 59096-02 C Glossary-3 267
- Glossary-4 59096-02 C 268
- 59096-02 C Glossary-5 269
- Glossary-6 59096-02 C 270
- Numerics 271
- Index-2 59096-02 C 272
- 59096-02 C Index-3 273
- Index-4 59096-02 C 274
- 59096-02 C Index-5 275
- Index-6 59096-02 C 276
- 59096-02 C Index-7 277
- Index-8 59096-02 C 278
- 59096-02 C Index-9 279
- Index-10 59096-02 C 280
Relacionado con productos y manuales para Los conmutadores de red Qlogic SANbox 5600 Series
(24 paginas)
(114 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales