Qlogic SANsurfer iSCSI HBA CLI Guía de usuario Pagina 66
- Pagina / 80
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5 – Non-interactive Mode Commands
-delchap (Delete a CHAP Entry)
5-10 SN0054621-00 B
Q
The HBA will be reset after this command is issued.
5.26
-delchap
(Delete a CHAP Entry)
Type the following command to delete a CHAP entry:
-delchap <HBA No.> <CHAP>
The HBA will be reset after this command is issued.
5.27
-pinfo
(HBA Port Information)
Type the following command to display the port information for the specified HBA:
-pinfo <HBA No.>
5.28
-isns
(iSNS Settings)
Type the following command to configure the iSNS settings:
-isns <HBA No.> [iSNS IP Address]
When the [iSNS IP Address] parameter is not specified, the iSNS client on the
specified HBA port is disabled.
The HBA will be reset after this command is issued.
5.29
-gcr
(Get Crash Record)
Type the following command to obtain crash record information for the specified
HBA port:
-gcr <HBA No.> <Crash Output File>
5.30
-rdf
(Restore Default Firmware Settings)
Type the following command to restore the specified HBA port’s firmware values to
the factory defaults:
-rdf <HBA No.>
The HBA will be reset after this command is issued.
- User’s Guide 1
- Page ii SN0054621-00 B 2
- SN0054621-00 B Page iii 3
- Table of Contents 5
- Page vi SN0054621-00 B 6
- SANsurfer iSCSI HBA CLI 7
- SN0054621-00 B Page vii 7
- Figure Page 8
- Table Page 8
- Introduction 9
- 1 – Introduction 10
- Technical Support 10
- 1-2 SN0054621-00 B 10
- Getting Started 11
- Port Alias: 12
- Non-interactive Mode 13
- Initial Installation 15
- Installation Instructions 17
- SN0054621-00 B 3-3 17
- 3 – Initial Installation 17
- 3-4 SN0054621-00 B 18
- SN0054621-00 B 3-5 19
- Red Hat/SuSE Linux/PPC 20
- Solaris SPARC/Solaris x86 20
- Uninstall Instructions 20
- 3-8 SN0054621-00 B 22
- Interactive Mode Commands 23
- HBA Options Menu 24
- HBA Network Settings Menu 25
- Display Network Settings 25
- Configure IP Settings 26
- (Command Line Option -ipdhcp) 26
- Using DHCP 26
- Using SLP 27
- (Command Line Option -isns) 27
- HBA Firmware Settings Menu 27
- (Command Line Option -c) 28
- Change HBA Alias Name 36
- Edit a Specific HBA Setting 37
- Configure iSCSI Settings 37
- (Command Line Option -n) 37
- Configure Firmware Settings 38
- Configure Device Settings 38
- Configure Basic Settings 39
- Configure Advanced Settings 40
- Restore Default HBA Settings 40
- (Command Line Option -rdf) 40
- 4 – Interactive Mode Commands 41
- SN0054621-00 B 4-19 41
- Display Bootcode Information 42
- (Command Line Option -binfo) 42
- Set Bootcode Mode 42
- SN0054621-00 B 4-21 43
- HBA Restore Factory Defaults 44
- (Command Line Option -rdh) 44
- HBA Information 44
- (Command Line Option -pinfo) 44
- Reset HBA 45
- (Command Line Option -b) 45
- Target Menu 46
- List Targets 46
- (Command Line Option -t) 46
- Bind Target 47
- (Command Line Option -pb) 47
- Unbind Target 47
- Configure Target Parameters 47
- Add a Target 48
- (Command Line Option -pa) 48
- Add a CHAP Entry 50
- Add a Default BIDI CHAP 50
- Edit a CHAP Entry 51
- (Command Line Option -edchap) 51
- Delete a CHAP Entry 51
- List LUN Information 52
- (Command Line Option -l) 52
- Diagnostic Menu 52
- Ping Target 53
- (Command Line Option -ping) 53
- Perform Loopback Test 53
- (Command Line Option -lb) 53
- (Command Line Option -rwt) 54
- Display HBA Statistics 54
- (Command Line Option -stat) 54
- SN0054621-00 B 4-33 55
- (Command Line Option -vpd) 56
- Set Working Adapter 56
- Non-interactive Mode Commands 57
- ■ Host name 59
- ■ Host version 59
- ■ Host type 59
- (Configure iSCSI Settings) 60
- (Perform Loopback Test) 63
- -dspchap 64
- (Display a CHAP Table) 64
- -chapmap 64
- (Restore HBA Settings) 67
- 5-16 SN0054621-00 B 72
- Index-8 SN0054621-00 B 80
Relacionado con productos y manuales para Redes Qlogic SANsurfer iSCSI HBA CLI
Redes Qlogic QLA 2342L Manual de usuario
(16 paginas)
(16 paginas)
Redes Qlogic iSR6250 Guía de instalación
(16 paginas)
(16 paginas)
Redes Qlogic iSR6142 Guía de instalación
(120 paginas)
(120 paginas)
Redes Qlogic iSR6152 Guía de instalación
(12 paginas)
(12 paginas)
Redes Qlogic 3000 SERIES Especificaciones
(114 paginas)
(114 paginas)
Redes Qlogic iSR6142 Manual de usuario
(12 paginas)
(12 paginas)
Redes Qlogic QLE2362 Guía de instalación
(122 paginas)
(122 paginas)
Redes Qlogic iSR6142 Guía de instalación
(12 paginas)
(12 paginas)
Redes Qlogic iSR6142 Guía de usuario
(172 paginas)
(172 paginas)
Redes Qlogic QLA2342 Guía de usuario
(108 paginas)
(108 paginas)
Redes Qlogic iSR6152 Guía de usuario
(166 paginas)
(166 paginas)
Redes Qlogic iSR6152 Guía de instalación
(122 paginas)
(122 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.541 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales